The construction of three-dimensional (3D) objects, with any desired surface patterns, is both critical to and easily achieved in macroscale science and engineering. However, on the nanoscale, 3D fabrication is limited to particles with only very limited surface patterning. Here, we demonstrate a self-assembly strategy that harnesses the strengths of well-established 2D nanoscale patterning techniques and additionally enables the construction of stable 3D polyhedral nanoparticles. As a proof of the concept, we self-assembled cubic particles with sizes as small as 100 nm and with specific and lithographically defined surface patterns. Full Article

Nature utilizes self-assembly to fabricate structures on length scales ranging from the atomic to the macro scale. Self-assembly has emerged as a paradigm in engineering that enables the highly parallel fabrication of complex, and often three-dimensional, structures from basic building blocks. Although there have been several demonstrations of this self-assembly fabrication process, rules that govern a priori design, yield and defect tolerance remain unknown. In this paper, we have designed the first model experimental system for systematically analyzing the influence of geometry on the self-assembly of 200 and 500 microm cubes and octahedra from tethered, multi-component, two-dimensional (2D) nets. We examined the self-assembly of all eleven 2D nets that can fold into cubes and octahedra, and we observed striking correlations between the compactness of the nets and the success of the assembly. Two measures of compactness were used for the nets: the number of vertex or topological connections and the radius of gyration. The success of the self-assembly process was determined by measuring the yield and classifying the defects. Our observation of increased self-assembly success with decreased radius of gyration and increased topological connectivity resembles theoretical models that describe the role of compactness in protein folding. Because of the differences in size and scale between our system and the protein folding system, we postulate that this hypothesis may be more universal to self-assembling systems in general. Apart from being intellectually intriguing, the findings could enable the assembly of more complicated polyhedral structures (e.g. dodecahedra) by allowing a priori selection of a net that might self-assemble with high yields. Full Article

We demonstrate mass-producible, tetherless microgrippers that can be remotely triggered by temperature and chemicals under biologically relevant conditions. The microgrippers use a self-contained actuation response, obviating the need for external tethers in operation. The grippers can be actuated en masse, even while spatially separated. We used the microgrippers to perform diverse functions, such as picking up a bead on a substrate and the removal of cells from tissue embedded at the end of a capillary (an in vitro biopsy). Full Article

We describe the fabrication of 3D membranes with precisely patterned surface nanoporosity and their utilization in size selective sampling. The membranes were self-assembled as porous cubes from lithographically fabricated 2D templates (Leong et al., Langmuir 23:8747-8751, 2007) with face dimensions of 200 microm, volumes of 8 nL, and monodisperse pores ranging in size from approximately 10 microm to 100 nm. As opposed to conventional sampling and filtration schemes where fluid is moved across a static membrane, we demonstrate sampling by instead moving the 3D nanoporous membrane through the fluid. This new scheme allows for straightforward sampling in small volumes, with little to no loss. Membranes with five porous faces and one open face were moved through fluids to sample and retain nanoscale beads and cells based on pore size. Additionally, cells retained within the membranes were subsequently cultured and multiplied using standard cell culture protocols upon retrieval. Full Article

In this communication, we demonstrate the concept of single-use, chemically triggered, reversible tools in the form of mobile grippers that can be used to manipulate micro-objects. Both the closing and opening of the mobile grippers are triggered by chemicals, namely acetic acid (CH(3)COOH) and hydrogen peroxide (H(2)O(2)), respectively. The grippers close and open en masse based on chemically triggered, mechanical property changes within trilayer joints patterned within the gripper, and no external power is needed for operation. We describe the actuation of the gripper using a multilayer thin film model and demonstrate the utility of the gripper by picking-and-placing 200 microm diameter tubes and beads. Our pick-and-place microgripper is a first step toward the development of functional Micro Chemo-Mechanical Systems (MCMS), which are actuated by chemistry as opposed to electricity [as in Micro Electro-Mechanical Systems (MEMS)]. Full Article